AI electronics builder

Build the device you've been meaning to make

Describe your idea in plain words — we'll pick the parts, draw the wiring and write the firmware for Arduino, ESP32 or Raspberry Pi Pico.

  • ESP32 DevKit V1
  • ESP32-C3 Super Mini
  • ESP32-S3 DevKitC-1
  • Arduino Uno
  • Arduino Nano
  • Raspberry Pi Pico
How it works

Three steps from an idea to a working board

  1. Describe the idea

    What the device should do and where it will live. If something is missing, the agent will ask.

  2. Get the project

    Plan, parts, wiring, firmware and an assembly guide — all in one project.

  3. Build and power up

    Tick off the wires as you connect them, upload the firmware — and the device comes to life.

See what the agent does — and why

Every stage shows up in the chat: the steps the agent took and the decisions it made.

Balcony weather station

Generation

ESP32 DevKit V1

3.3 V logic like the sensor and the display, plus Wi-Fi to spare.

Power
USB, 5 V
Refresh
every 10 seconds
Bus
I²C: sensor and display
U1ESP32 DevKit V1×1
U2BME280 sensor×1
U30.96″ OLED display×1
—Breadboard×1
—Male-to-male jumper wires×8
  • 3V3BME280 · VCC
  • GNDBME280 · GND
  • GPIO21BME280 · SDA
  • GPIO22BME280 · SCL
  • 3V3OLED · VCC
  • GNDOLED · GND
  • GPIO21OLED · SDA
  • GPIO22OLED · SCL
  • power
  • ground
  • I2C

main.cpp

#include <Adafruit_BME280.h>
#include "pins.h"

Adafruit_BME280 bme;

void setup() {
  Serial.begin(115200);
  Wire.begin(PIN_I2C_SDA, PIN_I2C_SCL);
  bme.begin(BME280_ADDRESS);
}
  • Parts

    With links to buy. What to buy and how many — no catalog hunting.

  • Wiring

    Checked against electrical rules. Logic levels, I²C addresses, USB current.

  • Code

    Compiled for real. Pins match the wiring, the firmware file is ready.

  • Chat

    The agent answers about your project. Ask why this resistor, or how to run it on a battery.

Six boards you can find in any shop

  • ESP32 DevKit V1Wi-Fi · Bluetooth
  • ESP32-C3 Super Minitiny · battery
  • ESP32-S3 DevKitC-1USB keyboards and mice
  • Arduino Unothe classic · 5 V
  • Arduino Nanocompact · 5 V
  • Raspberry Pi PicoRP2040 · UF2
Ready-made projects

Not sure where to start? Take a ready one.

It opens right away, with wiring, firmware and instructions. Then make it yours.

Who it's for

  • Makers and hobbyists

    You have the idea, but no wish to dig through pinouts and forum code.

  • Students

    A course project that explains why the circuit is built this way.

  • Robotics teachers

    A lesson-ready project with parts, wiring and step-by-step assembly.

  • Engineers

    A quick prototype to test an idea before designing your own PCB.

FAQ

Do I need to know how to code?
No. The agent writes and compiles the code. Ask about anything unclear in the project chat.
Where do I buy the parts?
Every part comes with shop search links. Equivalents from your parts drawer work too.
How do I flash the board?
Download the ready file and flash it following the guide in the Assembly tab. Flashing right from the browser is coming soon.

What shall we build today?

Describe your idea — in a few minutes you'll have the parts, the wiring and the firmware.

Try it